母线槽
 母线槽安装示意图
 母线槽功能单元
 插接箱
 密集型(CMC)
 高强型(CFW)
 空气型(KFM)
 耐火型(NHMC)
 铝合金型(LMC)
 铜铝复合型(KFM)
 防水型(FSMC)
 照明型(ZMC)
 高压共相型(GM)
 地面布线系统(CDY)
 滑触线(HSMX)
 电缆桥架
 XQJ-ZC、ZP、ZT
 XQJ-Y-TPC圆弧型桥架
 XQJ-DJ大跨距桥架
 XQJ-WQJ钢网式电缆桥架
 XQJ-LQJ铝合金桥架
 NHQJ-C耐火桥架
 XQJ-P轻型节能桥架
 BHQ1、2玻璃钢桥架
 XQJ-ZH组合式配线桥架
 XQJ-LQJ照明桥架
 XQJ-XV竖井
 电缆桥架附件
 XQJ-H安装支架
 XQJ-TPC附件
 
 
照明型(ZMC)
 
您的位置:首页 >> 产品展示 >> 照明型(ZMC)
ZMC照明母线系统
 

特点 Features
● 通过完全型式试验的低压成套开关设备和控制设备 (TTA),符合 IEC/EN 60 439-1 和 -2, GB7251.2-2006
● 简化工程,降低成本
● 使用专用连接器插接式连接,可快速安装
● 两端分接点,用于优化使用母线
● 各相可连接相等数量的插接单元,均衡电缆分配系统导线的电气载荷
● 标准型产品的防护等级为 IP54,通用性强
● 使用插接单元,可快速、灵活地重新分配载荷
● Type-tested low-voltage switchgear and controlgear assembly (TTA) to IEC/EN 60 439 -1 and -2, GB7251.2-2006
● Reduced planning costs through simplified engineering
● Quick-release plug-in connection for fast assembly
● Tap-off points on both sides for optimized utilization of the busbar
● Even electrical loading of the CD system conductors by connecting an equal number of tap-off plugs to each individual phase
● Versatility through high degree of protection to IP54 of the standard version
● Tap-off plugs allow fast, flexible load relocation.

干线单元 Trunking units

a 连接器 Locating section
b 连接端子 Connection terminal
c 插接口 Tap-off point
提供有长度为2m和3m的干线单元,包括长方形、镀锌金属外箱,灰白喷漆。
The trunking units are vavilable in lengths of 2m and 3m. They consist of a rectangular, galvanized metal housing with a white-grey paint finish.
并在一端或两端配备有以下导线:
● 单相 3 线,用于 L1+N (PE = 外壳)
● 双相母线,用于 L1+L2+N (PE = 外壳)
● 三相 5 线,用于 L1+L2+L3+N (PE = 外壳)
They are fitted with the following conductor runs on one or both sides:
● 2 for L1 + N (PE = housing)
● 3 for L1 + L2 + N (PE = housing)
● 4 for L1 + L2 + L3 + N (PE = housing)

在干线单元上,分接点的标准间隔 0.5 或 1m。
干线单元外箱用作PE导线。共有七种电流额定值:2×25A, 30A, 40A。
所有干线单元都有触摸保护插接口,用户可进行编码。
The tap-off points are spaced at regular intervals of 0.5 or 1m on the trunking unit.
The trunking unit housing acts as the PE conductor. Three current ratings are
available: 2×25A, 30A, 40A. All trunking units have touch-proof tap-off points, that vcan be coded by the user.

接线方法 Connection method

干线单元,包括馈电单元和法兰与干线单元之间,都可采用插接式连接进行装配,无需工具。在连接外壳时即自动建立PE回路。带有两个固定件的互锁机构,可防止干线单元、馈单元和法兰之间的连接松动。无需伸缩件。
The trunking units, including those with feeder units and flanges, are assembled without tools by straightforward plug-in connection. The PE path is established automatically when the housings are connected. An interlock mechanism with two fixings prevents a loosening of the connections between the trunking units, feeder units and flanges. No expansion compensation is required.

终端法兰 End flanges

这些法兰可防止直接接触母线两端。它们可适用于所有照母线系统。
These flanges provide protection against direct contact at the ends of the busbar run. They are suitable for use with all CD systems.

馈电法兰 Tap-off plugs

有两种型号:
● 进线馈电单元,2×25A, 30A 和 40A
● 终端馈电单元,2×25A, 30A 和 40A
每个单元标准提供有一个终端法兰。
三侧进线。使用公制 M25 或 M32 塑料电缆固定头,带线扣(非标准提供)。
Two variants are available:
● Entry feeder unit for 2×25A, 30A and 40A
● End feeder unit for 2×25A, 30A and 40A.
One end flange is included as standard with each unit.
Cable entry from three sides. Use metric M25 or M32 plastic cable glands with strain relief (not included as standard).

插接单元 Tap-off plugs

干线单元的插接口可插装绝缘封闭的插接单元。
有以下类型可供使用:
● 3 线或 5 线型,无熔芯,带卤阻燃电缆。
● 3 线或 5 线型,无熔芯,带接线端子和 M20 塑料电缆索环。
● 3 线型,带熔芯,8.5mm×31.5mm, gG (IEC) 和 gL (VDE) 型快速圆筒型
熔断器,带阻燃电缆。
● 3 线型和 5 线型,带熔芯,1 个或 3 个 8.5mm×31.5mm, gG (IEC) 和 gL
(VDE) 型快速圆筒型熔断器,带端子和 M20 塑料电缆索环。
The tap-off points on the trunking units accept insulated enclosed tap-off plugs.
The following versions are available:
● 3-pole and 5-pole versions without fuse base with halogen-free, flame-retardant cable.
● 3-pole and 5-pole version without fuse base with terminal and plastic M20 cable grommet.
● 3-pole versions with fuse base for 8.5mm×31.5mm type gG (IEC) and type gL (VDE) fast cylinder fuses, with halogen-free, flame-retardant cable.
● 3-pole and 5-pole versions with fuse bases for one or three 8.5mm×31.5mm type gG (IEC) and type gL (VDE) fast cylinder fuses; with terminal and plastic M20 cable grommet.