母线槽
 母线槽安装示意图
 母线槽功能单元
 插接箱
 密集型(CMC)
 高强型(CFW)
 空气型(KFM)
 耐火型(NHMC)
 铝合金型(LMC)
 铜铝复合型(KFM)
 防水型(FSMC)
 照明型(ZMC)
 高压共相型(GM)
 地面布线系统(CDY)
 滑触线(HSMX)
 电缆桥架
 XQJ-ZC、ZP、ZT
 XQJ-Y-TPC圆弧型桥架
 XQJ-DJ大跨距桥架
 XQJ-WQJ钢网式电缆桥架
 XQJ-LQJ铝合金桥架
 NHQJ-C耐火桥架
 XQJ-P轻型节能桥架
 BHQ1、2玻璃钢桥架
 XQJ-ZH组合式配线桥架
 XQJ-LQJ照明桥架
 XQJ-XV竖井
 电缆桥架附件
 XQJ-H安装支架
 XQJ-TPC附件
 
 
防水型(FSMC)
 
您的位置:首页 >> 产品展示 >> 防水型(FSMC)
FSMC全封闭树脂浇注防水母线槽
 
特点 Characteristic
 
● 防护等级IP68,具有优良的气密性和水密性
● 耐压达到5000V以上
● 短路容量大
● 整体绝缘,确保使用安全
● 电压降小,损耗低
● 机械强度高,可承受6焦耳的冲击力
● 外形尺寸小
● 不存在电腐蚀,无迷流
● 抗化学品腐蚀
● 抗真菌侵蚀,抗动物、昆虫咬嚼
● 抗紫外线
● 自熄性绝缘材料
● 防火等级F120
● 耐火:950℃/90min
● 防爆性能良好
● 无烟囱效应
● 可在全天候环境中使用
1) 可在人能短暂停留的环境中长期使用
2) 不受海拔高度限制
3) 可在户内、外最高污染等级4(*)的环境中长期使用
4) 可在有爆炸或火灾危险的场所使用
● 安装简便
● 免维护
● 规格范围广:100A~8000A
● 可提供特殊终端单元
● Outdoor IP68, Air and watertight wall bushings
● Break voltage up to 5000V
● High short circuit withstand
● Full insulated with cast resin ensuring the safe operation
● Low voltage drop and small losses
● High mechanical strength of standing the outer shock up to 6J
● Small external dimensions
● Electro erosion resistance
● Chemical resistance
● Resistance against fungi, animals, insects, rodent
● UV-resistance
● Self-extinguishing insulation
● Fire retarding wall bus hings F120
● Fire resistance: 950℃ for 1.5hrs
● EX-protected
● Non chimney effect
● Suitable for all-weather application
a) Suitable for long-term application in the areas as long as human can stay temporarily
b) Suitable for application at any attitude height
c) Suitable for long-term application in aggressive atmo spheres (Pollution Degree up to 4)
d) Suitable for application in explosive areas
● Simple erection
● Maintenance free
● Wide range from 100A~8000A
● Tailor made terminal-elements available
 
主要性能 Major Performance
 
■ FSMC的耐火性能
采用无毒、阻燃绝缘材料,确保安全;符合GB/T12666.6-1990A类特性,维持线路完整性90分钟以上;
外壳防护等级IP68,能经受消防龙头喷水,确保母线槽不短路;
正常环境中使用有良好的散热功能。
■ Fire Resistance
The FSMC insulation material is inflammable and emits no toxic gas to ensure safety, The whole FSMC busway system remains integrated for 90 minutes or above under the fire-resistant test in accordance with the national regulation GB/T12666.6-1990A. Protection Degree for the FSMC external casing reaches IP68, so as to ensure no short circuit when being watersprayed in case of fire. The FSMC bueway system has ideal heat dissipation performance during normal working environment.
■ FSMC的绝缘性能
常温下每节母线槽绝缘电阻不低于1000MΩ;
环境温度在100℃的情况下每节母线槽绝缘电阻不低于200MΩ。

■ Insulation
Under normal temperature, electric resistance for each FSMC element is not lower than 1000MΩ;
Under ambient temperature at 100℃, electric resistance for each FSMC element is not lower than 200MΩ.
■ FSMC的耐腐性能
无金属外壳,抗各种化学品腐蚀。
■ Chemical Resistance
The FSMC busway system without any metal external casing is resistant to various chemical erosions.
■ FSMC的耐水性能
外壳防护等级IP68(*),可长期在水中工作;可在电缆沟内使用。甚至埋地敷设。
■ Watertight
The FSMC busway system is suitable for long-term application in the water or cable tunnel or even to be laid under the ground, benefited from the external casing protection rating of IP68 (*).
■ FSMC的机械性能
能承受6焦耳的机械冲击;低温-50℃环境下长期使用不开裂。
■ Mechanical Strength
The FSMC busway system can stand mechanical shock up to 6J and does not crack for long term application at the temperature up to -50℃.
■ FSMC的安全性能
不存在空气间隙,无烟囱效应;母线毛刺或过载不会引起短路。
■ Safety
No air gap inside the FSMC busway system to ensure non chimney-effect. Furthermore, any burr remained or overload will not cause short circuit.
 
产品介绍 Product Inforduction
 
■ 用途
F SMC全封闭树脂浇注母线槽系统额定电流1 0 0 A ~8000A,外壳防护等级达到IP68。 FSMC母线槽不仅耐火,而且耐水、耐腐,可确保电源不中断,因此能广泛应用于不能停电的重要工程、涉及生命安全的公共设施工程、救火困难的高层建筑、存在爆炸危险的场所等。FSMC全封闭树脂浇注母线槽系统防护等级高、安全性强,设计、安装简便,基本免维护。
■ Application
The FSMC busway system of current rating from 100A~8000A has a degree of protection IP68 and high resistance to fire, water and erosion, is therefore wide applied in important projects where uninterrupted power supply is necessary, public facilities where life and property safety is crucial, high buildings where firefighting is difficult as well as the areas where explosive risks exist
and etc.
The FSMC busway system with its high degree of safety is simple to design, easy to install and ultimately maintenancefree.
■ 结构
FSMC全封闭树脂浇注母线槽系统,采用特殊配方的复合树脂和定量特选的混合材料相混合,制成高性能的绝缘材料FSMC-M28,将铜或铝母线直接浇注密封。绝缘材料FSMC-M28不含卤素,阻燃且不会释放出有毒气体;无金属外壳,在有迷流的环境中工作,不会发生外壳电腐蚀的现象;全天候产品,可长期在零下40℃的环境中工作,绝缘树脂不开裂;优良的耐水性能,可在水中长期工作,也可埋地敷设;A级耐火性,可在950~1000℃的火焰中工作90min以上,保持线路不中断;可在有爆炸危险、有腐蚀性液体的环境中长期工作;所采用的绝缘材料FSMC-M28,高温时仍能保持良好的绝缘性。FSMC母线并具有很高的机械强度,能承受6焦耳的机械冲击。
■ Construction
The concept of FSMC busway is based on the di rect encapsulation of copper or aluminum conductors with a high insulation material (FSMC-M28) consisting of compound resin with a specific content of selected mixtures. The FSMC-M28 is halogen free, inflammable and emits no toxic gas. There is no metallic external casing for the FSMC busway system, and consequently electro-erosion does not exist. The FSMC-M28 does not crack for long term operation at the temperature up to -50, which guarantees the whole busway system suitable for all weather application. The FSMC-M28 has high watertight performance, which ensures the whole busway system suitable for long-term application in the water or even to be laid under the ground. The FSMC-M28 remains good insulation performance during fire temperature, which leads the FSMC busway system achieving a fire resistance rating of Grade A - remaining normal operation for 90 minutes or above at fire temperature 950-1000℃, and suitable for long term application in explosive areas. The FSMC-M28 has high mechanical strength, which assures the FSMC busway system can stand mechanical shock up to 6J.
■ 导体
导体截面为矩形并带圆角,采用优质电解铜ETP99.9%,符合GB5585.2-1985/GB/T467-1997标准。FSMC全封闭树脂浇注母线槽提供两种标准产品:3相4线3P/100%N或3相5线3P/100%N/100%PE根据客户要求,我们可以提供200%的N相导体。其它特殊形式导体及直流应用也能提供,具体情况与我们的技术部门联系。
■ Construction
The FSMC conductor bars have a rectangular section with rounded edges, made of electrolytic copper 99.9% in accordance with the national regulations GB5585.2-1985/GB/T467-1997, and are produced in the following standard versions:
-3 phases 4 conductors 3P/100%N
-3 phases 5 conductors 3P/100%N/100%PE
The neutral up to 200% from the PH-section is able to be provided upon request.
Special versions with 3PH or for DC application are possible. We would advise you to consult our Technical Department on this matter.
■ 连接
两段母线间的机械及电气连接通过双面接触的特殊连接器来完成。采用先进的高强力矩螺栓,将两段母线连接,并保证足够的接触面积和可靠的电气连接。然后对连接完成的接头单元浇注高性能绝缘材料FSMC-M28使母线达到防松和绝缘的双重目的。
FSMC全封闭树脂浇注母线槽系统(包括接头在内)能达到IP68防护等级。在高强力矩螺栓的扭紧力未达到预先设定力矩时,系统自动拒绝安装。
■ Jointing
The electrical and mechanical jointing of the trunking elements is achieved by a special connect. The connect supported by large pressure plates is held by tightening a double headed torque bolt which ensures a high standard of pressure along with a secure electrical contact. The correct torque setting is achieved when the outer head shears at a pre-set torque level. The mechanical connection, junctions and element extremities are over cast with the FSMC-M28.
The FSMC busway system guarantees a degree of protection of IP68 over the total lengths. If the correct torque level on the connect is not reached, then it will not be possible to encase the joint with the mould.
■ 分接单元
我们能在母线任何位置提供分接输出单元,分接箱的额定电流从125A~1250A,并能根据要求安装保险丝、开关及断路器等。防护等级达到IP67/68。
■ Tap-off Units
We can supply elements with tap-off outlets at any position throughout the element. The tap-off boxes in ratings from 125A to 1250A, can be supplied fitted with fuse-switches or circuit breakers. Two standard versions are as follows:
- Protection Degree IP67
- Protection Degree IP68
■ 支撑件
根据FSMC全封闭树脂浇注母线槽系统不同的安装环境,我们会提供相应的安装支撑件。在一般情况下,我们建议每1.5米安装一个支撑件。
■ Suspension Brackets
For opt imum instal lat ion of the FSMC busways in eitherceilings, walls, floors or steel constructions, we would supply the relevant suspension brackets.
The recommended fixing distance for such brackets is 1.5m in normal conditions.
■ 结构单元
根据客户的要求,我们能提供各种适应项目的结构单元。
■ Trunking Units
Tailor-made elements according to clients' specifications give total flexibility throughout the project.
 
 
■ 优点
1 大电流容量:
标准产品额定电流600A-5000A。
2 低电压降:
选用优质导电材料制造及适当排列,具有较低的阻抗值及电压降。
3 高短路强度:
汇流排导体间及外部应用环氧树脂绝缘系统,具有耐高短路强度之机械冲击特性及高耐热能力。
4 高耐火性:
由于选用具难燃性及自熄性材料,耐火等级符合
UL94V0或IEC331相关要求。
5 高防护等级:
防火及防尘特性符合防护等级IP68之要求。
6 高信赖度:
以高可靠度之设计选用优质原料及配合先进制程,在正常使用条件下具有高信赖度及寿命特长之优点。
7 型小量轻及外貌优美:
模铸外壳上下被覆铝质护套可取代接地导体作为接地之用,以减轻重量,及缩小体积,并增加美观。
8 安装容易免保养:
因模铸外壳上下被覆铝质护套可避免搬运时之碰装损伤,而段间相接采用快速接法,无须使用特殊工具,安装容易,并可随指示确认已安全接续完成,在正常运转条件下几乎免保养。
9 系统设变弹性佳:
汇流排因采用特殊接头及插入式配件,拆解容易且不伤元件,在配电系统设计变更时可弹性配合其调整及变动。
■ Rabbet merit
1 Current capacity: Standard product rated current 600A-5000A.
2 Low voltage drop: Selects the high quality conducting material manufacture and the suitable arrangement, has the low resistance value and loss of
voltage.
3 High short circuit intensity:
The exterior application epoxy resin insulated system between the bus conductor and, has bears the high short circuit intensity the mechanical shock characteristic and high heat-resisting ability.
4 High fire resistance:
Because chooses the apparatus flame retardancy and from extinguishes the material, the fireproof rank conforms to UL94V0 or the IEC331 related request.
5 High protection rank:
The fire protection and the dustproof characteristic meet requirement of the protection rank IP68.
6 High faith:
Selects the high quality raw material and the coordinate advanced system regulation design of by the high reliability, has the high faith under the regular service condition and merit of life special skill.
7 The small amount is light and the appearance is
exquisite:
The die casting outer covering high and low superposition aluminum nature protective covering may substitute for the earth conductor as earth, reduces the weight, and the reduced volume, and increases artisticly.
8 Installs easily to exempt the maintenance:
Because the die casting outer covering high and low superposition aluminum nature protective covering may avoid time the transporting bumping installs the damage, but the section docks uses the fast connection, does not need to use the special tool, the installment is easy, and may continue safely along with the
instruction confirmation completes, exempts the maintenance nearly under the normal work condition.
9 The system supposes the variable elastic properties
to be good:
Because the bus uses the special attachment and the male accessory, opens the solution to be easy, and does not injury the part, when electrical power distribution system design alteration may the elasticity coordinate its adjustment and the change.

技术参数 Technical Data
 
 
 
标准结构单元 Standard Trunking Units
 
安装示例 Assembly Instructions